Abstract This test method deals with gray irons that are to be free of chill in the casting and to chilled irons that are to have a specific depth of chill in the casting. The purpose of the test is to determine the chilling tendencies of cast iron. The two tests are wedge test and chill test. Both tests shall be made in a core which may either be single cores or gang cores and a pouring practice shall be performed. The wedge test is generally better adapted to the higher strength gray irons. The accelerated cooling rate that shall induce the formation of a chill shall be brought about through the design of the test specimen. The chill test is better adapted to the softer grades of gray iron and should be used if the casting have a specified depth of chill. The chill in this type of test shall be induced by casting one edge of the test specimen against a metal or graphite chilled plate or block. Wedge test is simpler than chill test since in the wedge test, maintenance of chill blocks or plates is not necessary.Scope 1.1 These test methods for chill testing apply to gray irons that are to be free of chill in the casting and to chilled irons that are to have a specific depth of chill in the casting. Two test methods for determining the chilling tendencies of cast iron are covered as follows. For many applications, either test method will be satisfactory if test pieces of the proper dimensions are selected. 1.1.1 Test Method A, Wedge Test—This test is adapted for the higher-strength gray irons. The accelerated cooling rate to induce the formation of a chill is brought about through the design of the test specimen. This test method is simpler than Test Method B since maintenance of chill blocks or plates is not necessary. 1.1.2 Test Method B, Chill Test—This test is adapted for the softer grades of gray iron and should be used if the casting is to have a specified depth of chill. The chill in this type of test is induced by casting one edge of the test specimen against a metal or graphite chilled plate or block. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered to be part of the standard. 1.2.1 The metric equivalency charts in Figs. 1 and 2 are provided for information only. in. mm in. mm in. mm 1/32  0.8 3/8     9.5 1    25.4 1/16  1.6 7/16  12.1 11/4  31.8 3/32  2.4 1/2    12.7 11/2  38.1 1/8  3.2 9/16  14.3 13/4  44.4 3/16  4.8 11/16  17.5 2   50.8 1/4  6.4 3/4   19.0 21/2  63.5 5/16  7.9 13/16  20.6     1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

American National Standards Institute Inc.

Version

A0367-22 Active

A0367-11R17

A0367-11

A0367-00R99

A0367-60R05

Language

Select Language

Format

Select Format

What is a Redline?

Why Redline?

×

A PDF redline is a quick and easy way to compare all of the changes between the current, active standard and the previous version.

With a redline you’ll immediately see:

additions
deletions
and other changes between the two standards.

Save Time and Trouble!
With a Redline you no longer have to spend time trying to determine what has changed in the new standard! Redlines save you time and ensure you see what the changes are to the standard.

Price
When you select the “Standard + Redline” option you get both documents! Best of all, the cost of a Standard + Redline is only slightly more than buying the Active Standard by itself.

Close

Coming Soon!

Price: $50.00

Contact Sales

Add to Cart

Shipping & Handling

ASTM Shipping and Handling

×

Domestic Shipping
Domestic orders are delivered via United Parcel Service (UPS) or United States Postal Service (USPS). Transit
times average 3 to 5 business days. Please be aware that UPS will not deliver packages to Post Office Boxes.

Domestic Rush Orders
Please Contact Us.

International Standard Shipping
International orders are delivered via courier post services which can be either a postal service, courier
service, or a combination of both. Standard Service is untraceable. Please allow 4-7 weeks for delivery.
International Expedited Shipping
Please Contact Us.

Please be aware that carriers will not deliver packages to Post Office Boxes. Because of the variability of
customs processes and procedures in different countries, ASTM International cannot guarantee transit times to
international destinations. Customs duty and taxes are the responsibility of the consignee.

Shipping & Handling charges follow the rate schedule, below:

Order Total
Shipping & Handling Fee

Up to $50.00
$8.61

$50.01 to $100.00
$17.03

$100.01 to $150.00
$25.08

$150.01 to $250.00
$33.51

$250.01 to $500.00
$48.62

$500.01 to $750.00
$66.37

$750.01 to $1000.00
$81.11

$1000.01 to $1500.00
$105.87

$1500.01 to $2500.00
$138.54

$2500.01 to $4999.00
$183.15

$5000.00 to $higher
$FREE

Shipping and Handling charges are approximate. Additional charges may be incurred if your order requires multiple shipments. This does not apply to complete sets and sections.

Related

ASTM License Agreement

ASTM License Agreement

×

ASTM License Agreement

IMPORTANT- READ THESE TERMS CAREFULLY BEFORE ENTERING THIS ASTM PRODUCT.
By purchasing a subscription and clicking through this agreement, you are entering into
a contract, and acknowledge that you have read this License Agreement, that you understand
it and agree to be bound by its terms. If you do not agree to the terms of this License Agreement,
promptly exit this page without entering the ASTM Product.

1. Ownership:This Product is copyrighted, both as a
compilation and as individual standards, articles and/or documents (“Documents”) by ASTM
(“ASTM”), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 USA, except as may be
explicitly noted in the text of the individual Documents. All rights reserved. You
(Licensee) have no ownership or other rights in the ASTM Product or in the Documents.
This is not a sale; all right, title and interest in the ASTM Product or Documents
(in both electronic file and hard copy) belong to ASTM. You may not remove or obscure
the copyright notice or other notice contained in the ASTM Product or Documents.

2. Definitions.
A. Types of Licensees:
(i) Individual User:a single unique computer, with an individual IP address;
(ii) Single-Site:one geographic location or to multiple
sites within one city that are part of a single organization unit administered centrally;
for example, different campuses of the same university within the same city administered centrally.

(iii) Multi-Site:an organization or company with
independently administered multiple locations within one city; or an organization or
company located in more than one city, state or country, with central administration for all locations.
B. Authorized Users:any individual who has subscribed
to this Product; if a Site License, also includes registered students, faculty or staff member,
or employee of the Licensee, at the Single or Multiple Site.

3. Limited License.ASTM grants Licensee a limited,
revocable, nonexclusive, non-transferable license to access, by means of one or more
authorized IP addresses, and according to the terms of this Agreement, to make the uses
permitted and described below, each ASTM Product to which Licensee has subscribed.

A. Specific Licenses:
(i) Individual User:
(a) the right to browse, search, retrieve, display and view the Product;
(b) the right to download, store or print single copies
of individual Documents, or portions of such Documents, solely for Licensee’s own use.
That is, Licensee may access and download an electronic file of a Document (or portion
of a Document) for temporary storage on one computer for purposes of viewing, and/or
printing one copy of a Document for individual use. Neither the electronic file nor
the single hard copy print may be reproduced in anyway. In addition, the electronic
file may not be distributed elsewhere over computer networks or otherwise. That is, the
electronic file cannot be emailed, downloaded to disk, copied to another hard drive or
otherwise shared. The single hard copy print may only be distributed to others for their
internal use within your organization; it may not be copied. The individual Document downloaded
may not otherwise be sold or resold, rented, leased, lent or sub-licensed.

(ii) Single-Site and Multi-Site Licenses:
(a) the right to browse, search, retrieve, display and view the Product;
(b) the right to download, store or print single copies
of individual Documents, or portions of such Documents for the Authorized User’s personal
use, and to share such copies with other Authorized Users of Licensee within Licensee’s computer network;
(c) if an educational institution, Licensee is permitted to provide a
hard copy of individual Documents to individual students (Authorized Users) in a class at Licensee’s location;

(d) the right to display, download and distribute hard copies
of Documents for training Authorized Users or groups of Authorized Users.

(e) Licensee will undertake all necessary authentication
and verification processes to ensure only Authorized Users can access the ASTM Product.

(f) Licensee will provide ASTM with a list of authorized
IP (numeric IP domain addresses) addresses and, if Multi-Site, a list of authorized sites.

B. Prohibited Uses.
(i) This License describes all permitted uses. Any other
use is prohibited, is a violation of this Agreement and can result in immediate termination of this License.

(ii) An Authorized User may not make this Product, or
Documents, available to anyone other than another Authorized User, whether by Internet link,
or by permitting access through his or her terminal or computer; or by other similar or dissimilar means or arrangements.

(iii) Specifically, no one is authorized to transmit, copy,
or distribute any Document in any manner or for any purpose except as described in Section
3 of this License, without ASTM’s prior express written permission.  In particular,
except as described in Section 3, no one may, without the prior express written permission
of ASTM: (a) distribute or forward a copy (electronic or otherwise) of any article, file,
or material obtained from any ASTM Product or Document; (b) reproduce or photocopy any
standard, article, file, or material from any ASTM Product; (c) alter, modify, adapt,
or translate any standard, article, file, or material obtained from any ASTM Product;
(d) include any standard, article, file, or material obtained from any ASTM Product or
Document in other works or otherwise create any derivative work based on any materials
obtained from any ASTM Product or Document; (e) impose any charge for a copy (electronic or
otherwise) of any standard,article, file, or material obtained from any ASTM Product or
Document, except for normal printing/copying costs where such reproduction is authorized
under Section 3; or (f) systematically download, archive, or centrally store substantial
portions of standards, articles, files, or material obtained from any ASTM Product or
Document. Inclusion of print or electronic copies in coursepacks or electronic reserves,
or for distance learning use, is not authorized by this License and is prohibited without
ASTM’s prior written permission. 

(iv) Licensee may not utilize the Product, or access to
the Product, for commercial purposes, including but not limited to the sale of Documents,
materials, fee-for-service use of the Product or bulk reproduction or distribution of Documents
in any form; nor may Licensee impose special charges on Authorized Users for use of the
Product beyond reasonable printing or administrative costs.

C. Copyright Notice. All copies of material from an ASTM
Product must bear proper copyright notice in ASTM’s name, as shown in the initial page
of each standard, article, file or material. Obscuring, deletion or modification of
the copyright notice is not permitted. 

4. Detection of Prohibited Uses.
A. Licensee is responsible for taking reasonable measures
to prevent prohibited uses, and promptly notify ASTM of any infringements of copyright or
prohibited use of which Licensee becomes aware.  Licensee will cooperate with ASTM
in investigating any such prohibited uses and will take reasonable steps to ensure the
cessation of such activity and to prevent any reoccurrence.

B. Licensee shall use all reasonable efforts to protect
the Product from any use that is not permitted under this Agreement, and shall notify
ASTM of any use of which it learns or is notified.

5. Continued Access to Product.ASTM reserves the
right to terminate this License, upon written notice, if Licensee materially breaches
the terms of this Agreement.  If Licensee fails to pay ASTM any license or
subscription fees when due, ASTM will provide the Licensee with a 30-day period within
which to cure such breach.  No cure period will be provided for material breaches
relating to violations of Section 3 or any other breach likely to cause ASTM irreparable
harm.  If Licensee’s subscription to an ASTM Product terminates, further access to
the online database will be denied. If Licensee or Authorized Users materially breach
this License or make prohibited uses of material in any ASTM Product, ASTM reserves the
right to deny Licensee any access to the ASTM Product, in ASTM’s sole discretion. 

6. Delivery Formats and Service.
A. Some ASTM Products use standard Internet HTML format. 
ASTM reserves the right to change such format upon three [3] months’ notice to Licensee,
although ASTM will make reasonable efforts to use commonly available formats. 
The Licensee and the Authorized Users are responsible for obtaining at their expense
suitable Internet connections, Web browsers, and licenses for any software necessary
to view the ASTM Products.  

B. The ASTM Products are also available in Adobe Acrobat
(PDF) format to Licensee and its Authorized Users, who are solely responsible for installing
and configuring the appropriate Adobe Acrobat Reader software.   

C. ASTM shall use reasonable efforts to make online access
available on a continuous basis.   Availability will be subject to periodic
interruption and downtime for server maintenance, software installation or testing,
loading new files, and reasons beyond the control of ASTM. ASTM does not guarantee access,
and will not be liable for damages or refunds if the Product becomes unavailable temporarily,
or if access becomes slow or incomplete due to system back-up procedures, Internet
traffic volume, upgrades, overload of requests to servers, general network failures
or delays, or any other cause that may from time to time make the Product unavailable
for the Licensee or Licensee’s Authorized Users.

7. Terms and Fees.
A. The term of this Agreement is _____________ (“Subscription Period”).
Access to the Product is for the Subscription Period only. This Agreement will remain in effect
thereafter for successive Subscription Periods so long as annual subscription fees, as such may
change from time to time, are paid. Licensee and/or ASTM have the right to terminate this Agreement
at the end of a Subscription Period by written notice given at least 30 days in advance.

B. Fees:
8. Verification.ASTM has the right to verify compliance
with this Agreement, at its expense, and at any time during the course of normal business
hours. To do so, ASTM will engage an independent consultant, subject to a confidentiality
agreement, to review Licensee’s use of ASTM Product and/or Documents. Licensee agrees to
permit access to its information and computer systems for this purpose. Verification
will take place upon no less than 15 days notice, during normal business hours and in
a manner that does not interfere unreasonably with Licensee’s operations. If
verification reveals unlicensed or prohibited use of the ASTM Products or Documents,
Licensee agrees to reimburse ASTM for the costs incurred in verification and reimburse
ASTM for any unlicensed/prohibited uses. By invoking this procedure, ASTM does not waive
any of its rights to enforce this Agreement or to protect its intellectual property by
any other means permitted by law. Licensee acknowledges and agrees that ASTM may imbed
certain identifying or tracking information in the ASTM Products available on the Portal.

9. Passwords:Licensee must immediately notify ASTM
of any known or suspected unauthorized use(s) of its password(s), or any known or suspected
breach of security, including the loss, theft unauthorized disclosure of such password
or any unauthorized access to or use of the ASTM Product. Licensee is solely responsible
for maintaining the confidentiality of its password(s) and for ensuring the authorized
access and use of the ASTM Product. Personal accounts/passwords may not be shared.

10. Disclaimer of Warranty: Unless specified in this Agreement,
all express or implied conditions, representations and warranties, including any implied
warranty of merchantability, fitness for a particular purpose or non-infringement
are disclaimed, except to the extent that these disclaimers are held to be legally invalid.

11. Limitation of Liability: To the extent not prohibited by law,
in no event will ASTM be liable for any loss, damage, lost data or for special, indirect,
consequential or punitive damages, however caused regardless of the theory of liability,
arising out of or related to the use of the ASTM Product or downloading of the ASTM Documents.
In no event will ASTM’s liability exceed the amount paid by Licensee under this License Agreement.

12. General.
A. Termination:This Agreement is effective until
terminated. Licensee may terminate this Agreement at any time by destroying all copies
(hard, digital or in any media)of the ASTM Documents and terminating all access to the ASTM Product.
B. Governing Law, Venue, and Jurisdiction:This
Agreement shall be interpreted and construed in accordance with the laws of the
Commonwealth of Pennsylvania. Licensee agrees to submit to jurisdiction and venue in
the state and federal courts of Pennsylvania for any dispute which may arise under this
Agreement. Licensee also agrees to waive any claim of immunity it may possess.

C. Integration:This Agreement is the entire agreement
between Licensee and ASTM relating to its subject matter. It supersedes all prior or
contemporaneous oral or written communications, proposals, representations and warranties
and prevails over any conflicting or additional terms of any quote, order, acknowledgment,
or other communication between the parties relating to its subject matter during the term
of this Agreement. No modification of this Agreement will be binding, unless in writing
and signed by an authorized representative of each party.

D. Assignment:Licensee may not assign or transfer
its rights under this Agreement without the prior written permission of ASTM.

E. Taxes.Licensee must pay any applicable taxes,
other than taxes on ASTM’s net income, arising out of Licensee’s use of the ASTM Product
and/or rights granted under this Agreement.

Reprints and Permissions

Reprints and copyright permissions can be requested through the
Copyright Clearance Center

Details

Book of Standards Volume:
01.02

Developed by Subcommittee:

A04.21

Pages: 4

DOI: 10.1520/A0367-22

ICS Code: 77.140.80

Go to ASTM A367 at ASTM.org

Add your thoughts about the standard.

1375 - Demolition Materials (549) 1377 - Cartridge and Propellant Actuated Devices and Components (524) 4720 - Hose and Flexible Tubing (552) 4730 - Hose, Pipe, Tube, Lubrication, and Railing Fittings (1823) 5120 - Hand Tools, Nonedged, Nonpowered (1124) 5305 - Screws (781) 5306 - Bolts (996) 5310 - Nuts and Washers (864) 5330 - Packing and Gasket Materials (583) 5340 - Hardware, Commercial (953) 5905 - Resistor (753) 5910 - Capacitors (783) 5930 - Switches (1012) 5935 - Connectors, Electrical (4357) 5940 - Lugs, Terminals, and Terminal Strips (564) 5945 - Relays and Solenoids (733) 5950 - Coils and Transformers (856) 5960 - Electron Tubes and Associated Hardware (1630) 5961 - Semiconductor Devices and Associated Hardware (707) 6145 - Wire and Cable, Electrical (1629) 6240 - Electric Lamps (662) 6505 - Drugs and Biologicals (1343) 6515 - Medical and Surgical Instruments, Equipment, and Supplies (1907) 6520 - Dental Instruments, Equipment, and Supplies (790) 6530 - Hospital Furniture, Equipment, Utensils, and Supplies (745) 6610 - Flight Instruments (540) 6625 - Electrical and Electronic Properties Measuring and Testing Instruments (1241) 6640 - Laboratory Equipment and Supplies (1187) 6810 - Chemicals (1114) 8010 - Paints, Dopes, Varnishes, and Related Products (2046) 8030 - Preservative and Sealing Compounds (554) 8140 - Ammunition and Nuclear Ordnance Boxes, Packages and Special Containers (797) 8305 - Textile Fabrics (910) 8415 - Clothing, Special Purpose (660) 8455 - Badges and Insignia (3093) 8915 - Fruits and Vegetables (531) 9330 - Plastics Fabricated Materials (759) FACR (1647) ISDA (1776) ISDD (786) ISDF (1827) ISDN (581) MISC (1045) PACK (539) SESS (581)
Aerospace Material (225) Aircraft Air Conditioning, Heating, and Pressurizing Equipment (334) Aircraft Hydraulic, Vacuum, and De-icing System Components (263) Ammunition, 75mm through 125mm (192) Ammunition, over 30mm up to 75mm (208) Ammunition, through 30mm (349) Analytical Chemistry (180) Bombs (192) Building (414) Bulk Explosives (261) Cartridge and Propellant Actuated Devices and Components (524) Consumer Product Evaluation (267) Copper (192) Demolition Materials (549) Electrical and Magnetic Conductor (162) Electronics (153) Environmental Toxicology (187) Fire Control Computing Sights and Devices (338) Fire Control Radar Equipment, except Airborne (197) Fuzes and Primers (454) Geotechnical Engineering (217) GUN (640) Land Mines (276) Medical Device and Implant (427) Military Chemical Agents (156) Miscellaneous Aircraft Accessories and Components (231) Miscellaneous Fire Control Equipment (216) Nondestructive Testing (246) Nonferrous Metal and Nonferrous Alloy (367) Nuclear Technology (274) Optical Sighting and Ranging Equipment (451) Paint and Related Coating (456) Parachutes; Aerial Pick Up, Delivery, Recovery Systems; and Cargo Tie Down Equipment (324) Petroleum (378) Plastic Pipe (248) Pyrotechnics (175) Road and Paving (177) Rockets, Rocket Ammunition and Rocket Components (368) Rubber (166) Security System Pedestrian and Walkway Safety (157) Specialized Test and Handling Equipment, Nuclear Ordnance (150) Sports and Recreation (316) Steel (908) Torpedos and Components, Inert (258) (621)