List of Plastics Standards

• AWS G1.6 – SPECIFICATION FOR THE QUALIFICATION OF PLASTICS WELDING INSPECTORS FOR HOT GAS, HOT GAS EXTRUSION, AND HEATED TOOL BUTT THERMOPLASTIC WELDS (HISTORICAL)
• AWS G1.10M – GUIDE FOR THE EVALUATION OF HOT GAS, HOT GAS EXTRUSION, AND HEATEDTOOL BUTT THERMOPLASTIC WELDS
• AWS G1.1M/G1.1 – GUIDE TO ULTRASONIC ASSEMBLY OF THERMOPLASTICS (HISTORICAL)
• AWS G1.2M/G1.2 – SPECIFICATION FOR STANDARDIZED ULTRASONIC WELDING TEST SPECIMEN FOR THERMOPLASTICS
• AWS B2.4 – SPECIFICATION FOR WELDING PROCEDURE AND PERFORMANCE QUALIFICATION FOR THERMOPLASTICS
• ASTM PS106 – Provisional Standard Specification for Rods and Tubes of Polyethylene (PE)
• ASTM F3541 – Standard Practice for Sectional Repair of Existing Gravity Flow, Non-Pressure Pipelines and Conduits by Pushed or Pulled-In-Place Installation of Cured-In-Place Thermosetting Resin Pipe (CIPP)
• ASTM F3508 – Standard Guide for In-Situ Pipeline Renovation As Dual-Wall Composite Pipeline by Push/Pull Installation of Compressed-Fit Shape-Memory-Polymer Tubular (SMPT)
• ASTM F3240 – Standard Practice for Installation of Seamless Molded Hydrophilic Gaskets (SMHG) for Long-Term Watertightness of Cured-in-Place Rehabilitation of Main and Lateral Pipelines
• ASTM F3182 – Standard Practice for the Application of Spray-Applied Polymeric Liners Inside Pipelines for Potable Water
• ASTM F3097 – Standard Practice for Installation of an Outside Sewer Service Cleanout through a Minimally Invasive Small Bore Vacuum Excavation and Same Day Restoration
• ASTM F3033 – Standard Practice for Installation of a Single-Sized, Cured-In-Place Liner Utilizing an Inflatable Bladder for Resurfacing Manhole Walls of Various Shapes and Sizes
• ASTM F2984 – Standard Specification for Segmental Panel System for the Grout-in-Place-Liner (GIPL) Rehabilitation Method of Existing Man-Entry Size Sewers, Culverts, and Conduits
• ASTM F2985 – Standard Practice for Installation of a PVC Segmental Panel Liner System in Man-Entry Size Sewers and Conduits
• ASTM F2994 – Standard Practice for Utilization of Mobile, Automated Cured-In-Place Pipe (CIPP) Impregnation Systems
• ASTM F2831 – Standard Practice for Internal Non Structural Epoxy Barrier Coating Material Used In Rehabilitation of Metallic Pressurized Piping Systems
• ASTM F2719 – Standard Practice for Installation of Polyethylene (PE) and Encapsulated Cement Mortar Formed in Place Lining System (FIPLS) for the Rehabilitation of Water Pipelines (Withdrawn 2022)
• ASTM F2718 – Standard Specification for Polyethylene (PE) and Cement Materials for an Encapsulated Cement Mortar Formed in Place Liner System (FIPLS) for the Rehabilitation of Water Pipelines (Withdrawn 2022)
• ASTM F2599 – Standard Practice for Sectional Repair of Damaged Pipe By Means of an Inverted Cured-In-Place Liner
• ASTM F2561 – Standard Practice for Rehabilitation of a Sewer Service Lateral and Its Connection to the Main Using a One Piece Main and Lateral Cured-in-Place Liner
• ASTM F2019 – Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic Cured-in-Place (GRP-CIPP) Using the UV-Light Curing Method
• ASTM F1962 – Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings
• ASTM F1947 – Standard Practice for Installation of Folded Poly(Vinyl Chloride) (PVC) Pipe into Existing Sewers and Conduits
• ASTM F1867 – Standard Practice for Installation of Folded/Formed Poly (Vinyl Chloride) (PVC) Pipe Type A for Existing Sewer and Conduit Rehabilitation
• ASTM F1871 – Standard Specification for Folded/Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation
• ASTM F1735 – Standard Specification for Poly (Vinyl Chloride) (PVC) Profile Strip for PVC Liners for Rehabilitation of Existing Man-Entry Sewers and Conduits
• ASTM F1741 – Standard Practice for Installation of Machine Spiral Wound Poly (Vinyl Chloride) (PVC) Liner Pipe for Rehabilitation of Existing Sewers and Conduits
• ASTM F1743 – Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
• ASTM F1697 – Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-Wound Liner Pipe Rehabilitation of Existing Sewers and Conduit
• ASTM F1698 – Standard Practice for Installation of Poly(Vinyl Chloride)(PVC) Profile Strip Liner and Cementitious Grout for Rehabilitation of Existing Man-Entry Sewers and Conduits
• ASTM F1606 – Standard Practice for Rehabilitation of Existing Sewers and Conduits with Deformed Polyethylene (PE) Liner
• ASTM F1504 – Standard Specification for Folded Poly(Vinyl Chloride) (PVC) Pipe for Existing Sewer and Conduit Rehabilitation
• ASTM F1216 – Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
• ASTM E1863 – Standard Test Method for Analysis of Acrylonitrile by Gas Chromatography
• ASTM E1788 – Standard Test Method for Acidity in Acrylonitrile (Withdrawn 2022)
• ASTM D953 – Standard Test Method for Pin-Bearing Strength of Plastics
• ASTM D955 – Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics
• ASTM D957 – Standard Practice for Determining Surface Temperature of Molds for Plastics
• ASTM D882 – Standard Test Method for Tensile Properties of Thin Plastic Sheeting
• ASTM D883 – Standard Terminology Relating to Plastics
• ASTM D8366 – Standard Specification for Extruded and Compression Molded Shapes Made from Unfilled Poly(Vinylidene Fluoride) PVDF
• ASTM D8349 – Standard Classification System for and Basis of Specifications for Thermoplastic Joining Interface Materials for Creation of Joints Between Different Materials for the Production of End Items or Parts that are Intended to be Disassembled and/or Reassemb
• ASTM D8280 – Standard Test Method for Determination of the Blooming of Brominated Flame Retardants onto the Surface of Plastic Materials by Ion Chromatography
• ASTM D8195 – Standard Classification System and Basis for Specification for Polyethylene Terephthalate Film and Sheeting
• ASTM D8156 – Standard Classification System for and Basis of Specifications for Thermoplastic Elastomer Copolyester Molding and Extrusion Materials (TPC)
• ASTM D8133 – Standard Test Method for Determination of Low Level Phthalates in Poly(Vinyl Chloride) Plastics by Solvent Extraction—Gas Chromatography/Mass Spectrometry
• ASTM D8136 – Standard Test Method for Determining Plastic Film Thickness and Thickness Variability Using a Non-Contact Capacitance Thickness Gauge
• ASTM D8065/D8065M – Standard Classification System and Basis for Specification for Specifying Plastic Films
• ASTM D8069 – Standard Test Method for Determining Flexural Modulus of Full Section Pultruded Fiber Reinforced Polymer (FRP) Composite Members with Doubly Symmetric Cross Sections under Bending
• ASTM D8033 – Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials
• ASTM D8036 – Standard Test Method for Polyurethane Raw Materials: Determination of Dimer Ratio in Pure MDI
• ASTM D8019 – Standard Test Methods for Determining the Full Section Flexural Modulus and Bending Strength of Fiber Reinforced Polymer Crossarms Assembled with Center Mount Brackets
• ASTM D7990 – Standard Test Method for Using Reflectance Spectra to Produce an Index of Temperature Rise in Polymeric Siding
• ASTM D7991 – Standard Test Method for Determining Aerobic Biodegradation of Plastics Buried in Sandy Marine Sediment under Controlled Laboratory Conditions
• ASTM D7992/D7992M – Standard Practice for Elevated Temperature and Moisture Conditioning of Pultruded Fiber Reinforced Polymer (FRP) Composites Used in Structural Designs
• ASTM D7993 – Standard Guide for Analyzing Complex Phthalates
• ASTM D7997 – Standard Practice for Polyurethane Raw Materials: Gel Tests for Polyurethane Non-Foam Formulations
• ASTM D794 – Practice for Determining Permanent Effect of Heat on Plastics (Withdrawn 1998)
• ASTM D792 – Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
• ASTM D789 – Standard Test Method for Determination of Relative Viscosity of Concentrated Polyamide (PA) Solutions
• ASTM D790 – Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
• ASTM D787 – Standard Specification for Ethyl Cellulose Molding and Extrusion Compounds
• ASTM D788 – Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds
• ASTM D7856 – Standard Specification for Color and Appearance Retention of Solid and Variegated Color Plastic Siding Products using CIELab Color Space
• ASTM D785 – Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials
• ASTM D7823 – Standard Test Method for Determination of Low Level Phthalates in Poly (Vinyl Chloride) Plastics by Thermal Desorption—Gas Chromatography/Mass Spectrometry
• ASTM D7791 – Standard Test Method for Uniaxial Fatigue Properties of Plastics
• ASTM D7792/D7792M – Standard Practice for Freeze/Thaw Conditioning of Pultruded Fiber Reinforced Polymer (FRP) Composites Used in Structural Designs
• ASTM D7793 – Standard Specification for Insulated Vinyl Siding
• ASTM D7774 – Standard Test Method for Flexural Fatigue Properties of Plastics
• ASTM D7745 – Standard Practice for Testing Pultruded Composites
• ASTM D7710 – Standard Test Method for Determination of Volume and Density of Rigid and Irregularly Shaped Molded Cellular Materials (Withdrawn 2021)
• ASTM D7711 – Standard Guide for Description of Polymer Pellet Defects
• ASTM D7611/D7611M – Standard Practice for Coding Plastic Manufactured Articles for Resin Identification
• ASTM D7567 – Standard Test Method for Determining Gel Content in Crosslinked Ethylene Plastics Using Pressurized Liquid Extraction (Withdrawn 2015)
• ASTM D7568 – Standard Specification for Polyethylene-Based Structural-Grade Plastic Lumber for Outdoor Applications
• ASTM D756 – Practice for Determination of Weight and Shape Changes of Plastics Under Accelerated Service Conditions (Withdrawn 1998)
• ASTM D7486 – Standard Test Method for Measurement of Fines and Dust Particles on Plastic Pellets by Wet Analysis
• ASTM D7487 – Standard Practice for Polyurethane Raw Materials: Polyurethane Foam Cup Test
• ASTM D7474 – Standard Practice for Determining Residual Stresses in Extruded or Molded Sulfone Plastic (SP) Parts by Immersion in Various Chemical Reagents
• ASTM D7475 – Standard Test Method for Determining the Aerobic Degradation and Anaerobic Biodegradation of Plastic Materials under Accelerated Bioreactor Landfill Conditions
• ASTM D747 – Standard Test Method for Apparent Bending Modulus of Plastics by Means of a Cantilever Beam (Withdrawn 2019)
• ASTM D7471 – Standard Specification for CPT-Fluoropolymer Molding and Extrusion Materials
• ASTM D7472 – Standard Specification for EFEP-Fluoropolymer Molding and Extrusion Materials
• ASTM D7473/D7473M – Standard Test Method for Weight Attrition of Non-floating Plastic Materials by Open System Aquarium Incubations
• ASTM D7445 – Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)
• ASTM D746 – Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
• ASTM D7436 – Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology
• ASTM D7444 – Standard Practice for Heat and Humidity Aging of Oxidatively Degradable Plastics
• ASTM D7399 – Standard Test Method for Determination of the Amount of Polypropylene in Polypropylene/Low Density Polyethylene Mixtures Using Infrared Spectrophotometry
• ASTM D732 – Standard Test Method for Shear Strength of Plastics by Punch Tool
• ASTM D729 – Standard Specification for Vinylidene Chloride Molding Compounds (Withdrawn 2000)
• ASTM D7309 – Standard Test Method for Determining Flammability Characteristics of Plastics and Other Solid Materials Using Microscale Combustion Calorimetry
• ASTM D7310 – Standard Practice for Defect Detection and Rating of Plastic Films Using Optical Sensors
• ASTM D731 – Standard Test Method for Molding Index of Thermosetting Molding Powder
• ASTM D7292 – Standard Specification for Extruded, Compression-Molded, and Injection-Molded Basic Shapes of Polyamide-Imide (PAI)
• ASTM D7293 – Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI)
• ASTM D7251 – Standard Specification for Color and Appearance Retention of Variegated Color Plastic Siding Products (Withdrawn 2018)
• ASTM D7252 – Standard Test Method for Polyurethane Raw Materials: Determination of Monomer and Isomers in Isocyanates
• ASTM D7253 – Standard Test Method for Polyurethane Raw Materials: Determination of Acidity as Acid Number for Polyether Polyols

12Next