List of Fire and Flammability Standards

• ASTM E970 – Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source
• ASTM E906/E906M – Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using a Thermopile Method
• ASTM E84 – Standard Test Method for Surface Burning Characteristics of Building Materials
• ASTM E800 – Standard Guide for Measurement of Gases Present or Generated During Fires
• ASTM E814 – Standard Test Method for Fire Tests of Penetration Firestop Systems
• ASTM E662 – Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials
• ASTM E648 – Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source
• ASTM E603 – Standard Guide for Room Fire Experiments
• ASTM E535 – Standard Practice for Preparation of Fire-Test-Response Standards
• ASTM E3287 – Practice for Specimen Preparation of Fenestration Profiles Intended to Support Non-Combustible In-Fill Materials to Assess Surface Burning Characteristics
• ASTM E3202 – Standard Practice for Specimen Preparation and Mounting of Plastic Composites for Use as Deck Boards, Stair Treads, Guards or Handrails to Assess Surface Burning Characteristics
• ASTM E3134 – Standard Specification for Transportation Tunnel Structural Components and Passive Fire Protection Systems
• ASTM E3082 – Standard Test Methods for Determining the Effectiveness of Fire Retardant Treatments for Natural Christmas Trees
• ASTM E3048 – Standard Test Method for Determination of Time to Burn-Through Using the Intermediate Scale Calorimeter (ICAL) Radiant Panel
• ASTM E3020 – Standard Practice for Ignition Sources
• ASTM E3021/E3021M – Standard Guide for Evaluating the Relative Effectiveness of Building Systems to Resist the Passage of Products of Combustion Based on the Aggregation of Leakage Rates
• ASTM E2988 – Standard Practice for Specimen Preparation and Mounting of Flexible Fibrous Glass Insulation for Metal Buildings to Assess Surface Burning Characteristics
• ASTM E2989 – Standard Guide for Assessment of Continued Applicability of Reaction to Fire Test Reports Used in Building Regulation
• ASTM E2965 – Standard Test Method for Determination of Low Levels of Heat Release Rate for Materials and Products Using an Oxygen Consumption Calorimeter
• ASTM E2957 – Standard Test Method for Resistance to Wildfire Penetration of Eaves, Soffits and Other Projections
• ASTM E2912 – Standard Test Method for Fire Test of Non-Mechanical Fire Dampers Used in Vented Construction
• ASTM E2886/E2886M – Standard Test Method for Evaluating the Ability of Exterior Vents to Resist the Entry of Embers and Direct Flame Impingement
• ASTM E2874 – Standard Test Method for Determining the Fire-Test Response Characteristics of a Building Spandrel-Panel Assembly Due to External Spread of Fire
• ASTM E2837 – Standard Test Method for Determining the Fire Resistance of Continuity Head-of-Wall Joint Systems Installed Between Rated Wall Assemblies and Nonrated Horizontal Assemblies
• ASTM E2816 – Standard Test Methods for Fire Resistive Metallic HVAC Duct Systems
• ASTM E2749 – Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens
• ASTM E2750 – Standard Guide for Extension of Data from Penetration Firestop System Tests Conducted in Accordance with ASTM
• ASTM E2768 – Standard Test Method for Extended Duration Surface Burning Characteristics of Building Materials (30 min Tunnel Test)
• ASTM E2748 – Standard Guide for Fire-Resistance Experiments
• ASTM E2707 – Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure
• ASTM E2726/E2726M – Standard Test Method for Evaluating the Fire-Test-Response of Deck Structures to Burning Brands
• ASTM E2688 – Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics
• ASTM E2690 – Standard Practice for Specimen Preparation and Mounting of Caulks and Sealants to Assess Surface Burning Characteristics
• ASTM E2632/E2632M – Standard Test Method for Evaluating the Under-Deck Fire Test Response of Deck Materials
• ASTM E2652 – Standard Test Method for Assessing Combustibility of Materials Using a Tube Furnace with a Cone-shaped Airflow Stabilizer, at 750°C
• ASTM E2653 – Standard Practice for Conducting an Interlaboratory Study to Determine Precision Estimates for a Fire Test Method with Fewer Than Six Participating Laboratories
• ASTM E2599 – Standard Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics
• ASTM E2573 – Standard Practice for Specimen Preparation and Mounting of Site-Fabricated Stretch Systems to Assess Surface Burning Characteristics
• ASTM E2574/E2574M – Standard Test Method for Fire Testing of School Bus Seat Assemblies
• ASTM E2579 – Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics
• ASTM E2536 – Standard Guide for Assessment of Measurement Uncertainty in Fire Tests
• ASTM E2404 – Standard Practice for Specimen Preparation and Mounting of Textile, Paper or Polymeric (Including Vinyl) and Wood Wall or Ceiling Coverings, Facings and Veneers, to Assess Surface Burning Characteristics
• ASTM E2405 – Standard Test Method for Determination of Fire and Thermal Parameters of Materials Using an Intermediate Scale Test with Vertically Oriented Specimen (Withdrawn 2011)
• ASTM E2336 – Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems
• ASTM E2335 – Standard Guide for Laboratory Monitors
• ASTM E2307 – Standard Test Method for Determining Fire Resistance of Perimeter Fire Barriers Using Intermediate-Scale, Multi-story Test Apparatus
• ASTM E2280 – Standard Guide for Fire Hazard Assessment of the Effect of Upholstered Seating Furniture Within Patient Rooms of Health Care Facilities
• ASTM E2257 – Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies
• ASTM E2226 – Standard Practice for Application of Hose Stream
• ASTM E2230 – Standard Practice for Thermal Qualification of Type B Packages for Radioactive Material
• ASTM E2231 – Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics
• ASTM E2187 – Standard Test Method for Measuring the Ignition Strength of Cigarettes
• ASTM E2102 – Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
• ASTM E2061 – Standard Guide for Fire Hazard Assessment of Rail Transportation Vehicles
• ASTM E2067 – Standard Practice for Full-Scale Oxygen Consumption Calorimetry Fire Tests
• ASTM E2074 – Standard Test Method for Fire Tests of Door Assemblies, Including Positive Pressure Testing of Side-Hinged and Pivoted Swinging Door Assemblies (Withdrawn 2007)
• ASTM E2058 – Standard Test Methods for Measurement of Material Flammability Using a Fire Propagation Apparatus (FPA)
• ASTM E2032 – Standard Practice for Extension of Data From Fire Resistance Tests Conducted in Accordance with ASTM E 119
• ASTM E2010 – Standard Test Method for Positive Pressure Fire Tests of Window Assemblies (Withdrawn 2007)
• ASTM E1995 – Standard Test Method for Measurement of Smoke Obscuration Using a Conical Radiant Source in a Single Closed Chamber, With the Test Specimen Oriented Horizontally
• ASTM E1966 – Standard Test Method for Fire-Resistive Joint Systems
• ASTM E1895 – Standard Guide for Determining Uses and Limitations of Deterministic Fire Models (Withdrawn 2011)
• ASTM E1822 – Standard Test Method for Fire Testing of Stacked Chairs
• ASTM E1776 – Standard Guide for Development of Fire-Risk-Assessment Standards
• ASTM E176 – Standard Terminology of Fire Standards
• ASTM E1740 – Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wall Covering or Ceiling Covering Composites Using a Cone Calorimeter
• ASTM E1725 – Standard Test Methods for Fire Tests of Fire-Resistive Barrier Systems for Electrical System Components
• ASTM E1678 – Standard Test Method for Measuring Smoke Toxicity for Use in Fire Hazard Analysis
• ASTM E162 – Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
• ASTM E1623 – Standard Test Method for Determination of Fire and Thermal Parameters of Materials, Products, and Systems Using an Intermediate Scale Calorimeter (ICAL)
• ASTM E1590 – Standard Test Method for Fire Testing of Mattresses
• ASTM E1591 – Standard Guide for Obtaining Data for Fire Growth Models
• ASTM E1546 – Standard Guide for Development of Fire-Hazard-Assessment Standards
• ASTM E1529 – Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies
• ASTM E1537 – Standard Test Method for Fire Testing of Upholstered Furniture
• ASTM E1474 – Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
• ASTM E1472 – Standard Guide for Documenting Computer Software for Fire Models (Withdrawn 2011)
• ASTM E1352 – Standard Test Method for Cigarette Ignition Resistance of Mock-Up Upholstered Furniture Assemblies
• ASTM E1353 – Standard Test Methods for Cigarette Ignition Resistance of Components of Upholstered Furniture
• ASTM E1354 – Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
• ASTM E1355 – Standard Guide for Evaluating the Predictive Capability of Deterministic Fire Models
• ASTM E136 – Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750 °C
• ASTM E1317 – Standard Test Method for Flammability of Surface Finishes
• ASTM E1321 – Standard Test Method for Determining Material Ignition and Flame Spread Properties
• ASTM E119 – Standard Test Methods for Fire Tests of Building Construction and Materials
• ASTM E108 – Standard Test Methods for Fire Tests of Roof Coverings
• ASTM C1308 – Standard Test Method for Accelerated Leach Test for Measuring Contaminant Releases From Solidified Waste
• ASTM C1285 – Standard Test Methods for Determining Chemical Durability of Nuclear, Hazardous, and Mixed Waste Glasses and Multiphase Glass Ceramics: The Product Consistency Test (PCT)
• ASTM C1220 – Standard Test Method for Static Leaching of Monolithic Waste Forms for Disposal of Radioactive Waste
• ASTM C1174 – Standard Guide for Evaluation of Long-Term Behavior of Materials Used in Engineered Barrier Systems (EBS) for Geological Disposal of High-Level Radioactive Waste
• ASTM C1144 – Standard Test Method for Splitting Tensile Strength for Brittle Nuclear Waste Forms (Withdrawn 2018)