5220 - Inspection Gages and Precision Layout Tools規格の一覧

• SAE-AS23003 – Gages – Inspection for MS23002 Crimping Dies (for use with MS25036 Insulated Terminals)
• SAE-AS22520/18 – Crimping Tools, Terminal, Hand, Wire Termination In-Service Inspection Gages for AS22520/17 Crimping Tools
• SAE-AS22520/42 – Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gage for AS22520/41 Crimp Tools
• SAE-AS22520/43 – Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gage for AS22520/40 Crimp Tools
• SAE-AS22520/35 – Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gages for AS22520/34 Crimp Tools
• SAE-AS22520/39 – Crimping Tool, Terminal, Hand, Actuated, Wire Termination, In-Service Inspection Gage for AS22520/5, /37, /38, and /44 Crimp Tools
• NAS823 – Cast Surface Comparison Standard
• SAE-AS22520/3 – Crimping Tools, Terminal, Hand, Wire Termination, Inspection Gage for Type I and II Tools
• SAE-AS22520/6 – Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gages for Type III Tools (For AS22520/5 and /32 Crimp Tools)
• NAS526 – Gage, Stylus, Flushness for 100 Degrees Countersunk Flush Fasteners (See Notice of Withdrawal for Replacement Information)
• NAS527 – Inspection Procedure for Flash Fasteners (See Notice of Withdrawal for Replacement Information)
• NAS518 – Gage, 100 Deg., Flat Head Flushness
• MIL-HDBK-204 – Design of Inspection Equipment for Dimensional Characteristics
• FED-STD-346 – Gages, Wrench Opening (S/S by ANSI/ASME B107.17)
• ASME-B107.17M – Gages, Wrench Openings, Reference
• ASME-B47.1 – Gage Blanks
• GGG-P-441 – Plate, Angle, Adjustable and Solid (No S/S Document)
• GGG-P-453 – Plate, Surface, Cast Iron
• GGG-P-463 – Plate, Surface, (Granite) (Inch and Metric)
• GGG-B-461 – Block, Step, Machinists (No S/S Document)
• ASME-B47.1M – Gage Blanks
• A-A-59120 – Gauge, Surface Plate Flatness Checking
• A-A-59572 – Gage, Comparator, Electric (No S/S Document)
• GGG-G-61 – Gage, Plug and Ring, Plain and Thread
• GGG-B-121 – Bar, Sine, Plate Sine (and Fixtures)
• GGG-P-61 – Parallel, Steel and Cast-Iron, Precision Ground
• A-A-58089 – Comparator, Bench Type, Electronically Amplified
• MIL-STD-120 – GAGE INSPECTION (W/NOTICE 1 DTD 9 SEP 63) (NO S/S DOCUMENT)
• A-A-50685 – Level, Precision Master, Single Face
• MIL-STD-133 – CAGE, PLUG, PLAIN CYLINDRICAL, GO FOR MINOR DIAMETER OF STANDARD CLASS OF INTERNAL THREAD (NO S/S DOCUMENT)
• A-A-50767 – Analyzer, Surface Finish
• MIL-STD-118 – Gage, Snap, Plain Adjustable (No S/S Document)
• MIL-STD-134 – GAGE, PLUG, PLAIN CYLINDRICAL, NOT GO FOR MINOR DIAMETERS OF STANDARD CLASSES 3F INTERNAL THREAD (NO S/S DOCUMENT)
• MIL-STD-273 – Gage, Plug, Thread Setting, Class W, for GO Gages Unified Standard Classes 2A and 3A and American National Standard Class 3 External Threads (No S/S Documents)
• MIL-STD-274 – Gage, Plug, Thread, Setting, Class W, for LO (Not Go), Gages, Unified Standard Classes 2A and 3A and American National Standard Class 3 External Threads (No S/S Document)
• MIL-STD-1452 – GAGING, GENERAL PRINCIPLES OF (NO S/S DOCUMENT)
• MIL-STD-113 – Gage, Ring, Plain, Not Go (No S/S Document)
• MIL-STD-114 – Gage, Plug, Thread Go (Class X) for Unified American National Standard Internal Thread (No S/S Document)
• MIL-STD-116 – GAGE, RING, THREAD GO (CLASS X) AND RELATED SETTING PLUG GAGES, GO AND NOT GO PLAIN PLUG MINOR DIAMETER ACCEPTANCE CHECK GAGES FOR UNIFIED AND AMERICAN NATIONAL STANDARD EXTERNAL THREADS (NO S/S DOCUMENT)
• MIL-STD-115 – Gage, Plug, Thread Not Go Unified-American National Standard Internal Thread (No S/S Document)
• MIL-STD-117 – GAGE, RING, THREAD, LO (NOT GO) AND RELATED THREAD SETTING PLUG GAGES, GO AND NOT GO PLAIN PLUG MINOR DIAMETER ACCEPTANCE CHECK GAGES FOR UNIFIED AND AMERICAN NATIONAL STANDARD EXTERNAL THREADS (NO S/S DOCUMENT)
• MIL-STD-110 – Gage, Plug, Plain Cylindrical Go (No S/S Document)
• MIL-STD-111 – Gage, Plug, Plain Cylindrical, Not Go (No S/S Document)
• MIL-STD-112 – GAGE, RING, PLAIN, GO (NO S/S DOCUMENT)
• MS90486 – Gage, in Service Inspection: for Use with MS90485 Crimping Dies, (for Use with Copper Uninsulated Terminals) (S/S by SAE-AS5259/1)
• MS90488 – GAGE, IN SERVICE INSPECTION, FOR MS 90487 SHIELDED CONTACT CRIMPING TOOL (NO S/S DOCUMENT)
• MS25472 – Gage, In-Service-Inspection, for Use with MS25442 Crimping Dies (for Use with Aluminum Wire Terminals) (S/S by SAE-AS5259/1)
• MS27832 – GAGE – INSPECTION FOR MS27828 CRIMPING TOOL AND MS27831 MINIATURE CRIMPING TOOL (USE MIL-C-22520/3)
• MS75094 – GAGES-INSPECTION FOR MIL-T-55619 TOOL, CRIMPING, FOR COAXIAL, RADIO-FREQUENCY, CONNECTORS (NO S/S DOCUMENT)
• MS90406 – Gage, Ring, Spline (Go-No Go)
• MS90414 – GAGE, IN-SERVICE INSPECTION, FOR MS90413 TERMINAL CRIMPING TOOL (NO S/S DOCUMENT)
• MS25316 – GAUGES FOR MS25312 CRIMPING TOOL (NO S/S DOCUMENT)
• MS14038 – GAGE, IN-SERVICE INSPECTION, FOR MS14037 CONTACT CRIMPING TOOL (USE MIL-C-22520/3)
• MS25340 – GAGE,-INSPECTION, FOR MS 25037 CRIMPING TOOL, ELECTRIC TERMINALS
• MS3434 – TEST GAGE, CONTACT LOCATION AND RETENTION FEATURE, MIL-C-0081511 SERIES 1 AND 2 CONNECTORS
• MS23003 – GAGES, INSPECTION FOR MS23002 CRIMPING DIES (FOR USE WITH MS25036 INSULATED TERMINALS) (S/S BY SAE-AS23003)
• MS3435 – Test Gage, Contact Location and Retention Feature, MIL-C-0081511 Series 3 and 4 Connectors
• MS3460 – TEST GAGE, MIL-C-0026482 SERIES 1 OR MIL-C-81703 SERIES 2 CONTACT RETENTION FEATURE
• MS3462 – TEST GAGE, MIL-C-26482 SERIES 2 (CLASS N), MIL-C-81703 SERIES 3 (CLASS N) AND MIL-C-0081511 SERIES 3 AND 4 (CLASS L) CONTACT RETENTION FEATURE
• MS3461 – Test Gage, MIL-C-0026482 Series 2 or MIL-C-81703 Series 3 Contact Retention Feature
• MS3317 – GAGE, IN-SERVICE INSPECTION, FOR MS 3316 TERMINAL CRIMPING TOOL
• MIL-I-83992 – Inspection Machine (Measuring, Digital Readout, and Automatic Data Processing), Electronically Operated (No S/S Document)
• MS3151 – GAGE-IN-SERVICE INSPECTION, FOR MS3150 CRIMPING DIES
• MS3196 – GAGE IN SERVICE INSPECTION, FOR CONTACT CRIMPING TOOL
• MS3197 – GAGE PIN FOR SOCKET CONTACT ENGAGEMENT TEST (S/S BY SAE-AS31971)
• MS3199 – GAGE – IN-SERVICE INSPECTION. FOR MS3198 CONTACT CRIMPING TOOL
• MIL-G-83984 – Gage, Surface Plate Flatness Checking (S/S by A-A-59120)
• MIL-C-83988 – Comparator, Bench Type, Vertical Column, Electrically Amplified (S/S by A-A-58089)
• MIL-G-87955 – Gage, Snap, Adjustable, Dial Indicating (No S/S Document)
• MIL-C-83997 – Comparator Gage, Internal and External, Electronically Amplified (S/S by A-A-58089)
• MIL-G-87964 – Gage, Surface, Gage and Plate (No S/S Document)
• MIL-I-45177 – Instrument, Tracer, Surface Roughness (S/S by A-A-50767)
• MIL-D-45608 – Designs and Drawings, Inspection Equipment (S/S by DOD-D-1000)
• MIL-G-45653 – Gage, Cylindrical Plug and Ring, Plain
• MIL-G-45654 – Gage, Plug and Ring, Thread (No S/S Document)
• MIL-G-46382 – Gage, Snap, Thread Roll
• MIL-DTL-22520/43 – Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gage (S/S by SAE-AS22520/43)
• MIL-T-22910/4 – Tool, Gage-Inspection for M22910/2 Crimping Tool (S/S by MIL-T-22910/8)
• MIL-T-22910/5 – TOOL, HAND, GAGE-INSPECTION FOR M22910/3 CRIMPING TOOL (S/S BY MIL-T-22910/8)
• MIL-T-22910/8 – GAGE INSPECTION FOR M22910/7 CRIMPING TOOL (NO S/S DOCUMENT)
• MIL-S-45176 – Specimen, Comparison, Surface Roughness (Flat) with Carrying Case (S/S By ANSI-B46.1 now ASME-B46.1)
• MIL-C-22520/18 – Crimping Tools, Terminal, Hand, Wire Termination In-Service Inspection Gage for MIL-C-22520/17 Crimping Tool (S/S by SAE-AS22520/18)
• MIL-C-22520/26 – Crimping Tool, Terminal, Hand or Power Actuated, Wire Termination, in Service Inspection Gages for MIL-C-22520/25 Crimping Tool (No S/S Document)
• MIL-C-22520/35 – Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gauges for MIL-C-22520/34 Crimp Tools (S/S by SAE-AS22520/35)
• MIL-DTL-22520/39 – Crimping Tool, Terminal, Hand, Actuated, Wire Termination, In-Service Inspection Gage for (S/S by SAE-AS22520/39)
• MIL-DTL-22520/42 – Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gage (S/S by SAE-AS22520/42)
• MIL-G-10944 – Gage, Dimensional Control
• MIL-P-14207 – Packaging of Parts, Spare Parts, Tools and Equipment for Gage Kits, Pullover (No S/S Document)
• MIL-P-14245 – PACKAGING OF PULLOVER GAGE ASSEMBLIES AND ACCESSORY KIT.
• MIL-C-22520/3 – Crimping Tools, Terminal, Hand, Wire Termination; In-Service Inspection Gages (S/S by SAE-AS22520/3)
• MIL-C-22520/6 – Crimping Tools, Terminal, Hand, Wire Termination, In-Service Inspection Gages (S/S by SAE-AS22520/6)
• MIL-P-10310 – Packaging of Inspection Gages (Use MIL-G-10944)