List of MISC Standards

• AND10398 – METALS, DEFINITION OF DISSIMILAR (S/S BY MS33586)
• AND10396 – NUMBER-AIRCRAFT ENGINE CYLINDER LOCATION DESIGNATION (USE MIL-STD-802)
• AND10388 – LINES-CONVENTIONAL
• AND10387 – DRILL SIZES AND DRILLED HOLE TOLERANCES TWIST
• AND10385 – ALTERNATE POSITION-EXAMPLE
• AND10384 – CROSS SECTIONING-EXAMPLES FOR
• AND10383 – CUTTING PLANE-EXAMPLE FOR
• AND10382 – GAUGE DIMENSIONS-STANDARD WIRE AND SHEET METAL
• AND10381 – SYMBOLS-MATERIAL
• AND10379 – EQUIVALENTS-FRACTION AND DECIMAL
• AND10375 – COLOR-FLUID LINE IDENTIFICATION (USE MIL STD 1247)
• AND10367 – TOLERANCE-ALLOY STEEL SHEET AND STRIP (S/S BY FED-STD-48)
• AND10362 – TOLERANCES-CARBON STEEL BAR AND ROD (USE FED STD 48)
• AND10360 – TOLERANCE-CORROSION AND HEAT RESISTANT STEEL BARS, AND RODS AND WIRE (USE FED-STD-48)
• AND10355 – TOLERANCES-CARBON STEEL-SHEET AND STRIP (USE FED STD 48)
• AND10342 – REGULATOR INSTALLATION CLEARANCE- DC GENERATOR VOLTAGE
• AND10335 – INSTALLATION CLEARANCE-TYPE XIX DRIVE
• AND10334 – INSTALLATION CLEARANCE-TYPE XX DRIVE PROPELLER GOVERNOR
• AND10332 – STARTER-GENERATOR INSTALLATION CLEARANCE, TYPE XII DRIVE
• AND10328 – INSTALLATION CLEARANCE-TYPE XL-B DRIVE MAGNETO
• AND10313 – RELIEF VALVE INSTALLATION CLEARANCE-HYDRAULIC
• AND10312 – ELEMENT INSTALLATION CLEARANCE-ENGINE CYLINDER HEAD TEMPERATURE MEASURING
• AND10307 – PROPELLER GOVERNOR INSTALLATION CLEARANCE-AIRCRAFT ENGINE (FOR ENGINES OF 1000 TAKE OFF H.P. AND OVER)
• AND10306 – PROPELLER GOVERNOR INSTALLATION CLEARANCE AIRCRAFT ENGINE (FOR ENGINES OF 999 TAKE OFF H.P. OR LESS)
• AND10300 – INSTALLATION CLEARANCE&TYPE X DRIVE
• AND10237 – SPLINE, SERRATED (NO S/S DOCUMENT)
• AND10236 – TEMPLATE PROPELLER BLADE ANGLE CHECKING
• AND10235 – TEMPLATE-PROPELLER BLADE FEMALE
• AND10234 – TEMPLATE-PROPELLER BLADE MASTER MALE
• AND10223 – LEVERS-CORRELATION OF POWER AND CONDITION
• AND10222 – FITTINGS-SYNTHETIC TANK GENERAL FEATURES OF CONSTRUCTION (SUPERSEDED IN PART )COVER( BY MS-33595 AND IN PART )FLANGE( BY MS-33596)
• AND10221 – VAPOR PRESSURE CORRECTION CHART
• AND10220 – VAPOR PRESSURE CHART (NO S/S DOCUMENT)
• AND10219 – PLUG – 14 MM BRITISH TYPE SHIELDED SPARK (USE MIL-S-7886)
• AND10217 – PLUG – 14 MM SHIELDED SPARK (USE MIL-S-7886)
• AND10216 – THROTTLE-HANDLE DESIGN FOR ENGINE
• AND10215 – MOUNTING FLANGE-SINGLE TYPE MAGNETO (9 AND 14 CYL)
• AND10214 – COUPLING ASSEMBLIES-DOUBLE TYPE MAGNETO DRIVE
• AND10211 – MOUNTING FLANGE – DOUBLE TYPE MAGNETO
• AND10210 – FLANGE-SINGLE 12 CYLINDER 3 BOLT MAGNETO
• AND10206 – PLUG – SHIELDED AIRCRAFT ENGINE SPARK (USE MIL-S-7886)
• AND10201 – SCREENS AND GASKETS – DESIGNS REQUIREMENTS FOR CARBURETOR
• AND10150 – STARTER DIAGRAM – HAND CRANK FLEXIBLE SHAFT
• AND10132 – ALUMINUM BAR – STANDARD ALLOY AND TEMPER (24ST), AND SIZES OF RECTANGULAR
• AND10131 – ALUMINUM BAR – STANDARD ALLOYS, TEMPER AND SIZES OF SQUARE
• AND10130 – ALUMINUM ROD AND BAR – STANDARD ALLOYS, TEMPERS AND SIZES OF ROUND AND HEXAGON
• AND10126 – ALUMINUM WIRE – STANDARD CONDITIONS AND SIZES FOR SHEET, STRIP
• AND10125 – ALUMINUM WIRE – STANDARD ALLOYS, TEMPERS AND SIZES OF ROUND AND HEXAGON (FOR WELDING ROD AND GENERAL USE)
• AND10119 – ALUMINUM ALLOY – STANDARD CONDITIONS AND SIZES FOR SHEET AND STRIP (24S)
• AND10108 – TUBING – STANDARD SIZES FOR ALUMINUM ALLOY (61S) ROUND
• AND10107 – TUBING – STANDARD SIZES FOR ALUMINUM ALLOY (24ST) ROUND
• AND10106 – TUBING – STANDARD SIZES FOR ALUMINUM ALLOY (52SO) ROUND
• AND10104 – TUBING, STEEL, CORROSION RESISTANT, ROUND STANDARD DIMENSIONS FOR (NO S/S DOCUMENT)
• AND10102 – TUBING – STANDARD DIMENSIONS FOR ROUND SEAMLESS ALLOY STEEL (NO S/S DOCUMENT)
• AND10087 – SCREW-INSTALLATION AND LIMITATIONS FOR USAGE OF SELF TAPPING (USE MS 33749)
• AND10082 – FASTENER, INSTALLATION-SNAPSLIDE (S/S BY MS-21327)
• AND10080 – FITTING – INSTALLATION OF UNIVERSAL ELBOW (USE MS21345)
• AND10079 – TERMINAL – EYE AND FORK CABLE (NO S/S DOCUMENT)
• AND10074 – BOSS SPACING – HYDRAULIC (USE MS21343)
• AND10066 – CONNECTORS-ELECTRICAL, RECEPTACLES, INTEGRAL MOUNTING (USE MS33678)
• AND10065 – CONNECTION ASSEMBLY – FLEXIBLE, FLUID, STANDARD DESIGN OF (NO S/S DOCUMENT)
• AND10064 – Fittings – Installation of Flared Tube, Straight Threaded Connectors (Use MS21344)
• AND10049 – BOSSES- FLUID CONNECTION, INTERNAL STRAIGHT THREAD (S/S BY MS 33649)
• AND10010 – MOUNTING PAD AND DRIVE – AIRCRAFT ENGINE PROPELLER GOVERNOR OR HYDRO-CONTROL VALVE
• AND10009 – MOUNTING PAD AND DRIVE – SMALL AIRCRAFT ENGINE STARTER
• AND10008 – MOUNTING PAD AND DRIVE – AIRCRAFT ENGINE POWER TAKE-OFF (FLANGE TYPE)
• AND10005 – MOUNTING PAD AND DRIVE – AIRCRAFT TACHOMETER (SEE DWG AND20005)
• AND10003 – MOUNTING PAD AND DRIVE – AIRCRAFT ENGINE FUEL PUMP (SEE DWG AND20003)
• AND10001 – MOUNTING PAD AND DRIVE – TYPE 2 VACUUM AND HYDRAULIC POWER PUMPS
• AND10000 – DRIVE – TYPE 1 FLUID POWER PUMPS (SEE DWG AND20000)
• AN6560 – GROMMET AND WASHER-PARACHUTE PACK (USE MS22048)
• AN6290 – GASKET&STRAIGHT THREAD TUBE FITTING, BOSS (USE MS28778)
• AN6231 – SCRAPER&ROD, HYDRAULIC PISTON
• AN6011 – GAGE AND PANEL MOUNTING HIGH PRESSURE OXYGEN
• AN5772 – GAGE, DIAL INDICATING, PRESSURE (S/S BY MS&28064
• AN5771 – GAGE, SINGLE, 1-7/8 DIAL PRESSURE (S/S BY MIL-STD 28061)
• AN5769 – GAGE, HYDRAULIC SYSTEM PRESSURE (USE MS28063)
• AN5727 – GLASS, AIRCRAFT INSTRUMENT COVER (USE MS 28105)
• AN5547 – GENERATOR, TACHOMETER, FOUR POLE (USE MS28054)
• AN5544 – GENERATOR&TACHOMETER, TWO POLE (USE MS28054)
• AN5532 – INDICATOR, ENGINE SYNCHROSCOPE
• AN3496 – INVERTER&INSTRUMENT, CLASS A, 6 VOLT& SINGLE PHASE
• AN3352 – RELAY, 55 AMP, 2PST, UNSEALED, CLASS O (S/S BY MS24178)
• AN3252 – BLOCK-TERMINAL, FIVE STUD
• AN3249 – JACK & TIP VOLTMETER TEST
• AN3216 – SWITCH, CLASS D LIMIT (S/S BY MS25383)
• AN3207 – COVER-TERMINAL BLOCK
• AN3179 – INDUCTOR, 30 VOLT LABORATORY TEST (S/S BY MS-90306)
• AN3057 – ADAPTER&ELECTRICAL ACCESSORY TO CABLE
• AN2522 – LENS&24 INCH DOUBLE BEAM (USE MS25391)
• AN931 – GROMMET – ELASTIC (S/S BY MS35489)
• AN773 – FITTING ASSEMBLY, LOW PRESSURE DETACHABLE SWIVEL HOSE (USE MS-27404)
• AN669 – TERMINAL, WIRE ROPE, STUD (USE MS-21260)
• AN668 – TERMINAL, WIRE ROPE, SWAGING&EYE END
• AN667 – TERMINAL, WIRE ROPE, SWAGING-FORK END (USE MS-20667)
• AN666 – TERMINAL, WIRE ROPE, STUD (USE MS-21259)
• AN664 – BALL END, WIRE ROPE, SWAGING-SINGLE SHANK (USE MS-20664)
• AN663 – BALL END, WIRE ROPE, SWAGING-DOUBLE SHANK (USE MS-20663)
• AN658 – TERMINAL, WIRE ROPE SWAGING, FORK END (USE MS-20658)
• AN550 – SCREW WOOD, FLAT HEAD, 82 DEGREE (USE MS35492 OR 35494)

Previous123Next