List of Thermal Insulation Standards

• ASTM E96/E96M – Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
• ASTM C1363 – Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus
• ASTM C1371 – Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
• ASTM C1373/C1373M – Standard Practice for Determination of Thermal Resistance of Attic Insulation Systems Under Simulated Winter Conditions
• ASTM C1374 – Standard Test Method for Determination of Installed Thickness of Pneumatically Applied Loose-Fill Building Insulation
• ASTM C1340/C1340M – Standard Practice for Estimation of Heat Gain or Loss Through Ceilings Under Attics Containing Radiant Barriers by Use of a Computer Program
• ASTM C1335 – Standard Test Method for Measuring Non-Fibrous Content of Man-Made Rock and Slag Mineral Fiber Insulation
• ASTM C1338 – Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings
• ASTM C1304 – Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials
• ASTM C1313/C1313M – Standard Specification for Sheet Radiant Barriers for Building Construction Applications
• ASTM C1321 – Standard Practice for Installation and Use of Interior Radiation Control Coating Systems (IRCCS) in Building Construction
• ASTM C1303/C1303M – Standard Test Method for Predicting Long-Term Thermal Resistance of Closed-Cell Foam Insulation
• ASTM C1258 – Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation
• ASTM C1263 – Standard Test Method for Thermal Integrity of Flexible Water Vapor Retarders
• ASTM C1224 – Standard Specification for Reflective Insulation for Building Applications
• ASTM C1199 – Standard Test Method for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Using Hot Box Methods
• ASTM C1153 – Standard Practice for Location of Wet Insulation in Roofing Systems Using Infrared Imaging
• ASTM C1155 – Standard Practice for Determining Thermal Resistance of Building Envelope Components from the In-Situ Data
• ASTM C1158 – Standard Practice for Installation and Use of Radiant Barrier Systems (RBS) in Building Construction
• ASTM C1134 – Standard Test Method for Water Retention of Rigid Thermal Insulations Following Partial Immersion
• ASTM C1136 – Standard Specification for Flexible, Low Permeance Vapor Retarders for Thermal Insulation
• ASTM C1146 – Standard Guide for Prefabricated Panel and H-bar Insulation Systems for Vessels, Ducts and Equipment Operating at Temperatures Above Ambient Air
• ASTM C1129 – Standard Practice for Estimation of Heat Savings by Adding Thermal Insulation to Bare Valves and Flanges
• ASTM C1130 – Standard Practice for Calibration of Thin Heat Flux Transducers
• ASTM C1132 – Standard Practice for Calibration of the Heat Flow Meter Apparatus (Withdrawn 2002)
• ASTM C1114 – Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
• ASTM C1094 – Standard Guide for Flexible Removable Insulation Covers (Withdrawn 2010)
• ASTM C1101/C1101M – Standard Test Methods for Classifying the Flexibility or Rigidity of Mineral Fiber Blanket and Board Insulation
• ASTM C1104/C1104M – Standard Test Method for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation
• ASTM C1043 – Standard Practice for Guarded-Hot-Plate Design Using Circular Line-Heat Sources
• ASTM C1044 – Standard Practice for Using a Guarded-Hot-Plate Apparatus or Thin-Heater Apparatus in the Single-Sided Mode
• ASTM C1045 – Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
• ASTM C1046 – Standard Practice for In-Situ Measurement of Heat Flux and Temperature on Building Envelope Components
• ASTM C1055 – Standard Guide for Heated System Surface Conditions that Produce Contact Burn Injuries
• ASTM C1057 – Standard Practice for Determination of Skin Contact Temperature from Heated Surfaces Using a Mathematical Model and Thermesthesiometer
• ASTM C1058/C1058M – Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
• ASTM C1060 – Standard Practice for Thermographic Inspection of Insulation Installations in Envelope Cavities of Frame Buildings
• ASTM C1041 – Standard Practice for In-Situ Measurements of Heat Flux in Industrial Thermal Insulation Using Heat Flux Transducers (Withdrawn 2019)
• ASTM C1033 – Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation Installed Vertically (Withdrawn 2003)