Significance and Use

American National Standards Institute Inc.

4.1 This test method is useful when oils and fats are suspected as an ignition source or a fuel source in a fire.

4.1.1 The identification of oil and fat residues in samples from a fire scene can support the field investigator’s opinion regarding the origin and cause of the fire.

4.1.2 The positive identification of fatty acid(s) does not necessarily mean that the fire was caused by self heating.

4.2 This test method specifically identifies fatty acid derivatives. Oils and fats are comprised primarily of triglycerides (which are fatty acids attached to a glycerol backbone), and some free fatty acids. Free fatty acids and triglycerides are not easily analyzed by the traditional ignitable liquid extraction techniques. Solvent extraction and derivatization to FAME will enable identification by GC-MS.

4.2.1 The identification of an individual fatty acid in fire debris samples does not confirm the presence of oils or fats; however, there are times when large quantities of the oil or fat may be extracted. In such cases a more positive identification can be made.

4.2.2 Oils and fats containing fatty acids with no double bonds will generally have no tendency to self-heat. With increasing unsaturation (1, 2, and 3 double bonds), the tendency to self-heat also increases, such that polyunsaturated fatty acids (PUFAs), such as C18:3, have a high tendency to self-heat.

4.3 This test method is a sensitive separation technique and can detect quantities as small as 3 µL of oil or fat residue in an extract from a debris sample.

4.4 This test method shall be performed after all required traditional testing for ignitable liquid residues is completed.

4.5 This test method extracts liquids and residues from porous and nonporous materials of various sizes.

4.6 This test method can be hampered by coincident extraction of interfering compounds present in the fire debris samples.

4.7 This is a destructive technique and whenever possible the entire sample should not be used for the procedure. It is recommended that visual inspection be used to locate portions or areas exhibiting potential oily residue for sub-sampling which would preserve remaining portions for further analyses and also minimize solvent waste. The solvent extracted portions of the sample are not suitable for resampling.

4.8 Alternate methods of extraction, derivatization, or analysis exist and may be suitable for use in obtaining similar results and conclusions.

4.9 Biodiesel, an ignitable liquid, is a trans-esterified product containing FAMEs. The FAME compounds in biodiesel can be detected in fire debris using many fire debris extraction techniques followed directly by GC-MS analysis. Derivatization is not necessary to identify the FAMEs in biodiesel.

4.10 For more information on oils, FAME, and fire debris analysis, see the references listed.3, 4, 5, 6

Scope

1.1 This test method covers the extraction, derivatization, and identification of fatty acids indicative of vegetable oils and fats in fire debris and liquid samples. This procedure will also extract animal oils and fats, as these are similar in chemical composition to vegetable oils and fats. Herein, the phrase “oils and fats” will be used to refer to both animal and vegetable derived oils and fats.

1.2 This test method is suitable for successfully extracting oil and fat residues having 8 to 24 carbon atoms.

1.3 The identification of a specific type of oil (for example, olive, corn, linseed) requires a quantitative analysis of the fatty acid esters and is beyond the scope of this test method.

1.4 This test method cannot replace the requisite knowledge, skills, or abilities acquired through appropriate education, training, and experience and should be used in conjunction with sound professional judgment.

1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Go to ASTM E2881 at ASTM.org

Add your thoughts about the standard.

1375 - Demolition Materials (549) 1377 - Cartridge and Propellant Actuated Devices and Components (524) 4720 - Hose and Flexible Tubing (552) 4730 - Hose, Pipe, Tube, Lubrication, and Railing Fittings (1823) 5120 - Hand Tools, Nonedged, Nonpowered (1124) 5305 - Screws (781) 5306 - Bolts (996) 5310 - Nuts and Washers (864) 5330 - Packing and Gasket Materials (583) 5340 - Hardware, Commercial (953) 5905 - Resistor (753) 5910 - Capacitors (783) 5930 - Switches (1012) 5935 - Connectors, Electrical (4357) 5940 - Lugs, Terminals, and Terminal Strips (564) 5945 - Relays and Solenoids (733) 5950 - Coils and Transformers (856) 5960 - Electron Tubes and Associated Hardware (1630) 5961 - Semiconductor Devices and Associated Hardware (707) 6145 - Wire and Cable, Electrical (1629) 6240 - Electric Lamps (662) 6505 - Drugs and Biologicals (1343) 6515 - Medical and Surgical Instruments, Equipment, and Supplies (1907) 6520 - Dental Instruments, Equipment, and Supplies (790) 6530 - Hospital Furniture, Equipment, Utensils, and Supplies (745) 6610 - Flight Instruments (540) 6625 - Electrical and Electronic Properties Measuring and Testing Instruments (1241) 6640 - Laboratory Equipment and Supplies (1187) 6810 - Chemicals (1114) 8010 - Paints, Dopes, Varnishes, and Related Products (2046) 8030 - Preservative and Sealing Compounds (554) 8140 - Ammunition and Nuclear Ordnance Boxes, Packages and Special Containers (797) 8305 - Textile Fabrics (910) 8415 - Clothing, Special Purpose (660) 8455 - Badges and Insignia (3093) 8915 - Fruits and Vegetables (531) 9330 - Plastics Fabricated Materials (759) FACR (1647) ISDA (1776) ISDD (786) ISDF (1827) ISDN (581) MISC (1045) PACK (539) SESS (581)
Aerospace Material (225) Aircraft Air Conditioning, Heating, and Pressurizing Equipment (334) Aircraft Hydraulic, Vacuum, and De-icing System Components (263) Ammunition, 75mm through 125mm (192) Ammunition, over 30mm up to 75mm (208) Ammunition, through 30mm (349) Analytical Chemistry (180) Bombs (192) Building (414) Bulk Explosives (261) Cartridge and Propellant Actuated Devices and Components (524) Consumer Product Evaluation (267) Copper (192) Demolition Materials (549) Electrical and Magnetic Conductor (162) Electronics (153) Environmental Toxicology (187) Fire Control Computing Sights and Devices (338) Fire Control Radar Equipment, except Airborne (197) Fuzes and Primers (454) Geotechnical Engineering (217) GUN (640) Land Mines (276) Medical Device and Implant (427) Military Chemical Agents (156) Miscellaneous Aircraft Accessories and Components (231) Miscellaneous Fire Control Equipment (216) Nondestructive Testing (246) Nonferrous Metal and Nonferrous Alloy (367) Nuclear Technology (274) Optical Sighting and Ranging Equipment (451) Paint and Related Coating (456) Parachutes; Aerial Pick Up, Delivery, Recovery Systems; and Cargo Tie Down Equipment (324) Petroleum (378) Plastic Pipe (248) Pyrotechnics (175) Road and Paving (177) Rockets, Rocket Ammunition and Rocket Components (368) Rubber (166) Security System Pedestrian and Walkway Safety (157) Specialized Test and Handling Equipment, Nuclear Ordnance (150) Sports and Recreation (316) Steel (908) Torpedos and Components, Inert (258) (621)